en
United Kingdom - english
Wed Nov 22 11:52:31 2017
Wed Nov 22 11:52:31 2017
CC612 Charge Controller

CC612 Charge Controller

  • Smart Grid capable via OCPP communication protocol
  • Compact design, only 22.6 mm wide
  • Supports local load management
  • PLC modem (ISO 15118) integrated
  • RCD Type A sufficient for the charging station, RCD Type B not required

The charge controller monitors charging system internal hardware, such as the meter, the user interface board or the socket. It is characterized by its compact design and size that in turn enables intelligent, small and cost effective charging systems. To enable the charge controller to communicate, a backend system is required. Given that most backend providers strictly adhere to the Open Charge Point Protocol (OCPP), the charge controller is OCPP 1.5 and OCPP 1.6 compliant. All specified messages in OCPP are supported as well as some vendor-specific extensions based on the DataTransfer message. Integration tests with the backend implementations of providers such as Vattenfall, Bosch, NTT and DRIIVZ have been successfully carried out. The charge controller can be operated as an “always on” system that is always connected to a mobile network. The controller supports 2.5G Edge and 3G UMTS mobile networks. Connectivity for online operation requires a SIM card (which is not included in delivery). User interaction is facilitated using an RFID module, which consists of an RFID card reader and LEDs. Charging is initiated by holding a valid RFID card close to the reader. In offline operation, the charge controller can optionally allow charging without authorization or it can authorize users based on RFID and a local white list of authorized RFID cards.

  • Features
  • Applications
  • Accessories
  • Ordering information
  • Downloads
  • Charge controller acc. to IEC 61851-22 (mode 3)
  • It can be configured as either a Master or Slave
  • The charge controller can be integrated into a single or three-phase system up to 80 A
  • Smart Grid enabled using standard OCPP functionality
  • OCPP 1.5 and OCPP 1.6 compliant with JSON, SOAP and Binary implementation
  • Supports 2.5G Edge and 3G UMTS mobile networks with an integrated 3G modem in all Master devices
  • Two USB interfaces:
    – CONFIG for local configuration
    – Other is used an extension port for peripheral USB devices (Ethernet/WiFi home applications)
    – Master/slave hardware configuartion
  • Control-pilot and proximity signal management
  • Universal charge plug control (support for different vendors of sockets)
  • Configurable support for one additional household socket
  • Can connect to eHZ or Modbus meters and to meters with an S0 interface
  • User interface board for customer-specific applications
  • Configurable 3-channel input/output extension interface for additional functionality
  • An integrated DC sensor (only an external type A RCD is required). Various cable lengths can be selected.
  • Internal temperature sensors
  • A Peer Group Mechanism where a set current is shared between a group of charge controllers
  • Optional integrated ISO/IEC 15118 power line communication (PLC) for plug & charge and load management systems
  • Local and remote configuration
  • electric vehicle (EV) charging stations, wall boxes or street light charging points

 

Optional accessories for CC612 Charge Controller


DesignationArt. No.
RFID110-L1 with RJ45 cable (length 500 mm)B94060110
Measuring current transformer* W15BS (Cable length 1500 mm)B98080065
Measuring current transformer* W15BS-02 (Cable length 180 mm)B98080067
Measuring current transformer* W15BS-03 (Cable length 320 mm)B98080068
DPM2x16FPB94060120
* The measuring current transformer has an internal diameter of 15 mm.

Variants of CC612 Charge Controller


TypeMaster/
Slave
ModemMeterDC sensorPLC* hardwareLEDsUser interfaceArt. No.
CC612-1M3PRMaster3GeHZ and S0 interfaceXXReady, Alarm, PLCXB94060001
CC612-2M3PRMaster3GModbus and S0 interfaceXXReady, Alarm, PLCXB94060003
CC612-1S0PRSlaveeHZ and S0 interfaceXXReady, Alarm, PLCXB94060005
CC612-2S0PRSlaveModbus and S0 interfaceXXReady, Alarm, PLCXB94060007
CC612-2M3RMaster3GModbus and S0 interfaceXReady, AlarmXB94060009
CC612-2S0RSlaveModbus/S0XReady, AlarmXB94060010
The charge controller only works in combination with the measuring current transformer, which must be ordered separately.
* Optional and enabled by a software update

Downloads for CC612 Charge Controller

Category

Language

Category Product Language Date Size Download